WaveSurfer

WaveSurfer

WaveSurfer

WaveSurfer

WaveSurfer

WaveSurfer

424

422

434

432

454

452

Bandwidth
(@ 50 )

200 MHz

350 MHz

500 MHz

Rise Time (Typical)

1.75 ns

1 ns

750 ps

Input Channels

4

2

4

2

4

2

Display

10.4” Color flat-panel TFT-LCD, 800 x 600 SVGA, touch screen

Sample Rate (single-shot)

1 GS/s (all channels), 2 GS/s max (interleaved mode).

Sample Rate (RIS mode)

50 GS/s

Standard Record Length

1 Mpts/Ch (all channels), 2 Mpts/Ch (interleaved mode).

Standard Capture Time

up to 1 ms at full sample rate

Vertical Resolution

8 bits

Vertical Sensitivity (V/div)

1 mV/div–10 V/div (1 MΩ); 1 mV/div –2 V/div (50 Ω)

Vertical (DC Gain) Accuracy

±(1.5% + 0.5% of full scale)

Vertical Offset Range

±1 V (1-20 mV/div), ±10 V (50-200 mV/div), ±100 V (500 mV–10 V/div)

Bandwidth Limit

20 MHz

20 MHz, 200 MHz

Maximum Input Voltage

CAT I: 400 Vmax (DC + Peak AC ≤ 5 kHz) with 1 MΩ input. 5 Vrms with 50 Ω input

Input Coupling

AC, DC, GND (DC and GND for 50 Ω)

Input Impedance

1 MΩ || 16 pF, or 50 Ω ±1%,

Probing System

BNC or ProBus

Probes

One PP007 (2.5 mm) per channel standard

Time Base Range

1 ns/div–1000 s/div

500 ps/div–1000 s/div

200 ps/div–1000 s/div

Time Base Accuracy

10 ppm

Trigger Modes

Normal, Auto, Single, and Stop

Trigger Sources

Any input channel, External, Ext/10, or line; slope and level unique to each source (except for line trigger)

Trigger Coupling

DC, AC, HF, HFRej, LFRej

Pre-trigger Delay

0–100% of full scale

Post-trigger Delay

0–10,000 divisions

Trigger Hold-off

2 ns to 20 s or 1 to 99,999,999 events

Internal Trigger Level Range

±5 div from center

External Trigger Range

EXT/10 ±5 V; EXT ±500 mV

Standard Triggers

Edge

Triggers when signal meets slope (positive, negative, or Window) and level condition.

Glitch

Triggers on positive or negative glitches with widths selectable from 2.5 ns to 20 s or on intermittent faults. Includes exclusion mode (trigger on intermittent faults by specifying the normal width period).

Width

Triggers on positive or negative pulse widths selectable from 2.5 ns to 20 s or on intermittent faults. Includes exclusion mode (trigger on intermittent faults by specifying the normal width period).

Logic (Pattern)

Logic combination (AND, NAND, OR, NOR) of 5 inputs (4 channels and external trigger input). Each source can be high, low, or don’t care. The High and Low level can be selected independently.

TV-Composite Video

Triggers selectable fields (1, 2, 4, or 8), Positive or Negative slope, for NTSC, PAL, SECAM, or non-standard video (up to 1500 lines).

Optional SMART Triggers
(WS-ADVTRIG option)

Runt

Trigger on positive or negative runts defined by two voltage limits and two time limits. Select between 2 ns and 20s. Includes exclusion mode (trigger on intermittent faults by specifying the normal width or period).

Slew Rate

Trigger on edge rates. Select limits for dV, dt, and slope. Select edge limits between 2 ns and 20 s. Includes exclusion mode (trigger on intermittent faults by specifying the normal width or period).

Interval (Signal or Pattern)

Triggers on intervals selectable between 2 ns and 20 s.

Dropout

Triggers if signal drops out for longer than selected time between 2 ns and 20 s. Includes exclusion mode (trigger on intermittent faults by specifying the normal width or period).

Qualified (State or Edge) Triggers on any input source only if a defined state or edge occurred on another input source. Delay between sources is 2 ns to 20 s, or 1 to 99,999,999 events. Includes exclusion mode (trigger on intermittent faults by specifying the normal width or period).

Measure, Zoom, and Math Tools

Standard Parameter Measurements

Up to 6 of the following parameters can be calculated at one time on any waveform: Amplitude, Area, Base (Low), Cyclic Area, Cyclic Mean, Cyclic RMS, Cyclic Std. Deviation, Delay, Duty, Fall Time (90%-10%), Fall Time (80%-20%), Frequency, Maximum, Mean, Minimum, Overshoot+, Overshoot-, Period, Peak-Peak, Phase, Rise Time (10%-90%), Rise Time (20%-80%), RMS, Skew, Standard Deviation, Top (High), Width+, Width-. Measurements may be gated.

Zooming

Use front panel QuickZoom button, or use touch screen or mouse to draw a box around the zoom area.

Standard Math

Operators include Sum, Difference, Product, Ratio, and FFT (up to 25 kpts with power spectrum output and rectangular, VonHann, and FlatTop windows). 1 math function may be defined at a time.

Extended Math

Adds the following additional math functions: Absolute Value, Averaging (summed and continuous),

(WS-MATHSURF Option)

Derivative, Envelope, Enhanced Resolution (to 11 bits), Floor, Integral, Invert, Reciprocal, Roof, Square, and Square Root. Also adds chaining of two math functions and rescaling to different units.

WaveStream Fast Viewing Mode

Intensity

Not Available

Number of Channels

Not Available

Max. Sampling Rate

Not Available

Waveforms/second (continuous)

Not Available

Operation

Not Available

Analog Persistence

Type

Analog or color-graded.

Saturation

Variable saturation level, adjustable from front panel.

Aging Time

Adjustable from 500 ms to infinity.

Operation

Front panel toggle between ON Analog, ON Color, or OFF (plus software user interface ON/OFF and type selectability). When ON, persistence applied to all waveforms.

Automatic Setup

Auto Setup

Automatically sets timebase, trigger, and sensitivity to display a wide range of repetitive signals. Vertical Find Scale automatically sets the vertical sensitivity and offset for the selected channel

Setup and Waveform Storage

Front Panel and
Instrument Status

Save to the internal hard drive, over the network, or to a USB connected peripheral device.

Waveform Traces

Save to one of four internal memories with 16 bit resolution for recall/comparison

Waveform Data

Save to the internal hard drive, over the network, or to a USB connected peripheral device.

Documentation and Connectivity

Printing

Connect to any Windows XP-compatible printer using the 25-pin D-type female (Centronics) printer port. Load any standard Windows XP printer driver onto the unit as future needs require.

Email

Configure the unit to send an email of a screen image in a variety of formats using MAPI (i.e. through a default email program) or SMTP (no additional program needed).

Waveform Memories

Save waveform data as a reference trace to be compared to channels, zooms, or math functions.

Waveform File Data

Save waveform data in the following formats: Binary, ASCII, Excel, Mathcad, MATLAB.

Screen Image

Save a screen image to the internal hard drive, a user-supplied USB memory stick, or any other peripheral connected to one of the three USB 2.0 ports. Image can be saved in a variety of formats, and with white or black background.

Waveform Labeling
(Annotation)

Attach up to 10 labels to any combination of waveforms. Labels appear on screen images.

Hardcopy Front Panel Button

Configure the front panel Hardcopy button to send an email, save a screen image, save waveform file data, and save to the clipboard.

Networking

Standard 10/100Base-T Ethernet interface (RJ-45 connector). Connect to any network using DHCP with automatically assigned IP address.

Remote Control

Via Windows automation, or via LeCroy Remote Command Set (via Ethernet or GPIB)

USB Ports

3 USB ports (one on front of instrument) support Windows compatible devices

External Monitor
Port Standard

15-pin D-Type female SVGA-compatible connector for external color display

Parallel Port

25-pin D-type female (Centronics)

Serial Port

9-pin D-type male (not for remote oscilloscope control)

Audio Port

Mic Input, Line Input, Line Output

GPIB Port (Accessory)

Supports IEEE– 488.2 (using NI USB-GPIB-B)

Outputs

Calibrator

1 kHz square wave, +1.0 V into 1 MΩ, output on front panel test point and ground lug

Control Signals

Rear Panel: TTL level, BNC output; Choice of trigger ready, trigger out, pass/fail status.(output resistance 300 Ω ±10%)

Environmental and Safety

Temperature (Operating)

+5 °C to +40 °C

Temperature (Non-Operating)

-20 °C to +60 °C

Humidity (Operating)

5% to 80% relative humidity (non-condensing) at 2 30 °C. Upper limit derates to 55% relative humidity (non-condensing) at +40 °C.

Humidity (Non-Operating)

5% to 95% relative humidity (non-condensing) as tested per MIL–PRF–28800F.

Altitude (Operating)

up to 3048 m (10,000 ft) at up to 25 °C

Altitude (Non-Operating)

up to 12,190 m (40,000 ft)

Vibration (Operating)

Random vibration, 0.31 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes

Vibration (Non-Operating)

Random vibration, 2.4 grms 5 Hz to 500 Hz, 15 minutes in each of three orthogonal axes

Functional Shock

20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total

Certification

UL (Std. UL 61010-1 2nd Edition) & cUL (Std. CSA C22.2 No. 61010-1-04) Listed. CE Compliant. EMC Directive 89/336/EEC; EN 61326:1997/A3:2003. Low Voltage Directive 73/23/EEC; EN 61010-1:2001.

Physical Dimensions

Dimensions (HxWxD)

260 mm x 340 mm x 152 mm (10.25" x 13.4" x 6"). Excluding accessories and projections.

Net Weight

6.8 kg (15 lbs). Excluding accessories.

General

Power (AC)

90-264 Vac, 47-63 Hz (90-132 Vac, 380-420 Hz); Max. Power Consumption: 200 VA

Power (DC)

DC Power and Battery Power Input 19-25 Vdc. DC Power IN = 1 IEC320 Port. Battery Power IN = 2 IEC320 Ports (no loss of power when changing batteries).

Warranty and Calibration

Three year warranty. Calibration recommended yearly.